CO—555 CALIBRATION ANVIL
ASTM C-805

For periodic calibration of concrete test hammer CO-550, complete with hammer guide

Dimension (l x w x h) : 20 x 20 x 30 cm
Gross Weight : 30 kg

CO—500 MODULUS OF ELASTICITY IN CONCRETE TEST SET

For measuring average axial deformation of concrete cylindrical sample during compression test, cast alumunium, dial indicator 0.001 x 5 mm

Dimension (l x w x h) : 30 x 30 x 35 cm
Gross Weight : 5 kg

BI-100 SPECIFIC GRAVITY OF SEMI—SOLID BITUMINOUS MATERIALS

ASTM D-70 AASHTO T-228

For determining the specific gravity of semi-solid bituminous materials, asphalt cement, and soft tar pitches by use of a picnometer

BI-101 Picnometer
Hubbart type, 24 ml capacity 1 Pc

BI-102 Picnometer
Hubbart type, 25 ml capacity 1 Pc

GE-642 Thermometer
ASTM 63 C, 8-32oC 1 Pc

Also required, but....

8BI-230A LABORATORY PENETRATION TEST SET
ASTM D-5, AASHTO T-49

For determining consistency of bituminous materials

BI-231A Penetrometer
Electric control box, 220 V-AC variable timer, ON-OFF and START switch for automatic plunger release cast alumunium frame, 4 1/2" dial indicator, 400 x 0.1 mm dial, knob control : manual + electric weight of needle and plunger : 50 gr. 1 Set

BI....

SO-250 PLATE BEARING TEST SET
ASTM D-1194 AASHTO T-235

For determining ultimate bearing capacity of soil on place by means of field loading test.

SO-251A Hydraulic Jack
50 tons capacity, manometer read out, hand operated.

Consist of :
SO-251.2 Manometer
6" dia., 50 tons capacity, 0.5 tons increament 1 Pc

GE-682 Hidraulic Cylinder
50 tons capacity 1 Pc

GE-691 Hidraulic Hand....

CO—410 VIBRATING TABLE

Steel construction 50 x 50 cm table Separated control box, variabel speed up to 3.600 rpm. For compacting aggregate in steel container or concrete sample in cube / cylinder mold.

Dimension (l x w x h) : 55 x 55 x 85 cm
Gross Weight : 70 kg

SO-360B LABORATORY CBR TEST SET
ASTM D-1883, AASHTO T-193

For determining the bearing ratio of soil.

SO-361B Mechanical Loading Machine
Steel frame, hand operated, two speeds, 10.000 lbs cap., 1.954" piston dia. 1 Set

SO-362 CBR Mold
Machined steel, 6" i.d, 7" weight, 2" height of collar 3 Pcs

SO-363 Spacer Dish
Machined steel, 5 15/16" dia., 2.416"....

Triple Beam Balance, OHAUS 750 SW

Special Features

The Ohaus Triple Beam Balance (750-SW) is well-equipped to handle any weighing job, whether you´re weighing solids, liquids, powders or even animals.
The top loading Triple Beam Balance Series is known world wide as for its durability and versatility to accommodate a range of lab applications.

• Attachment weights included to....

Hydraulic Cylinder

GE-681 Hydraulic Cylinder 30 capacity
GE-682 Hydraulic Cylinder 50 capacity
GE-683 Hydraulic Cylinder 100 capacity
GE-684 Hydraulic Cylinder 150 capacity
GE-685 Hydraulic Cylinder 200 capacity

Hydraulic Hand Pump
GE-690 Hand Pump 10.000 psi, single acting
GE-691 Hand Pump 10.000 psi, double acting

Hydraulic Electric Pump
Electric, 220 V-AC, 750 Watt, 1 Phase.
GE....

GE-174 / GE-191 / GE-200
Oven (Memmert)
Universal oven, double walled metal shield.
temperature range from room temperature t0 200oC
GE-171 Drying Oven 14 ltr capacity, internal dimension (l x w x h) 320 x 240 x 175 mm
GE-172 Drying Oven 32 ltr capacity, internal dimension (l x w x h) 400 x 320 x 250 mm
GE-173 Drying Oven 39 ltr capacity, internal dimension (l x w x h) 480 x 320 x 250....

BI-220A Loss on Heating/Thin-Film Test
ASTM D-6/D-1754
AASHTO T-47/T-179

For determining the loss in mass (exclusive of water) of asphaltic compounds after heating
BI-221 Resolving Shelf Oven Variable temperature oven, cas alumunium rotating shelf, 5-6 RPM, external electromotor drive, 220 V-AC, 1400 Watt. 1 Set
GE-390 Thin Box 55 mm i.d. approx.
alumunium sheet, seamless 12 Pcs
GE-643....

BI-150A Saybolt Viscosimeter
ASTM D-88 AASHTO T-72

For determining saybolt viscosity of petroleum products at specified temperature between 21.1 and 98.8 C.
BI-151 Viscosimeter Stainless steel bath, motor stirer, 220 V-AC, Thermostat control panel, 2 tubes capacity 1 Set
BI-154 Viscosimeter Tube Brass, seamless, provided with tips and tip wrench 2 Pcs
BI-155 Tube Wrench T-wrench 1 Pc....

GE-150 / GE-152 / GE-157 / GE-159 / GE-161
Cent O-Gram Balance
GE-150 Cent O-Gram Balance 311 gr capacity 0.01 sensitivity

GE-151
Cent O-Gram Balance 311 gr capacity 0.01 sensitivity with dial type adjustment

Triple Beam Balance
GE-152 Triple Beam Balance 2.610 gr capacity 0.1 sensitivity.
Supplied complete with weights.

GE-153 Dial O-Gram Balance 2.610 gr capacity 0.1 sensitivity....

GE-101.6 / GE-137 / GE-140
Proving Ring

Precision measuring device, high grade steel with plated finishing 3/4" tapped hole at both end. Supplied complete with dial and calibration chart.

GE-101.1 Proving Ring 100 kg capacity
GE-101.2 Proving Ring 250 lbs capacity
GE-101.3 Proving Ring 500 lbs capacity
GE-101.4 Proving Ring 1.000 lbs capacity
GE-101.5 Proving Ring 2.000 lbs....

Liquid Limit Test Set
ASTM D-4318 AASHTO T-89

For determining liquit limit of soil sample.
SO-311 Liquid Limit Device Hand operated, brass cup, hard rubber base 1 Set
SO-312 ASTM Grooving Tool Machined steel, head gauge 1 Pc
SO-313 Cassagrande Grooving Tool Brass plate 1 Pc
GE-390 Thin Box Alumunium, 60 gr capacity 12 Pcs
GE-396 Glass Plate Galss, 10 mm thick, 30 x 30 cm 1 Pc....

MI-130 Rain Gauge
Bucket type 100 cm2 mouth area, made of metal sheet, supplied complete with measuring glass with special scale.

AG-700 Los Angeles Abrassion Machine
ASTM C-131 AASHTO T-96

For measuring degradation of mineral aggregates from abrassion, impact and grinding.
AG-701 Los Angeles Abrassion Machine 1 Set
Frame Welded steel frame, 8 and 12 cm (steel profile)
Drum 1/2" thick steel plate
28" inner diameter
20" inner width
Automatic Counter Digital, module system for easy maintenance....

CO-330 Hydraulic Concrete Beam Testing Machine
ASTM C-78

For determining the flexural strength of concrete beam by using a simple beam with third point loading. 100 kN cap., hidraulic hand pump, manometer reading, sample size 15 x 15 60 cm, welded steel construction

LABORATORY TEST SIEVE

Coarse Series ;

AG-200 A Sieve 4"
Mesh 101.6 mm opening
AG-201 A Sieve 3 1/2"
Mesh 88.9 mm opening
AG-202 A Sieve 3"
Mesh 76.2 mm opening
AG-203 A Sieve 2 1/2"
Mesh 62.5 mm opening
AG-204 A Sieve 2"
Mesh 50.8 mm opening
AG-205 A Sieve 1 3/4"
Mesh 44.4 mm opening
AG-206 A Sieve 1 1/2"
Mesh 38.1 mm opening
AG....

SO-150 A, DYNAMIC CONE PENETROMETER

For rapid determination of field CBR value (rapid quality control).
SO-151 Handle Stainless steel 1 Pc
SO-152 Hammer Machined steel, Painted, 8 kg weight 1 Pc
SO-153 Guide Rod Stainless steel, 16 mm dia drop height 575 mm 1 Pc
SO-154 Anvil Machined steel, welded, painted 1 Pc
SO-155A Penetration Rod Stainless steel, 16 mm dia, 75 cm effective length....